Best Hot Air Rework Station Tutorial for Mobile Phones

Best Hot Air Rework Station Tutorial for Mobile Phones

How to clean a tip in soldering iron there are two ways to clean the tip You can use a brass sponge or or a piece of cotton for cleaning different companies are manufacturing, soldering iron but only goots soldering iron is the best to use now in analog hot air station, there are two knob Air and heater Heater element exists in Handle that is directly controlled by this knob If you'd turn it on the button this red light gets on also you turn this button as per need

when this light blinks It means you Heater element Get warm Besides, there is a Heater inside the Handle and it gets it red when the heat gun is continuously on Means is now is too much hot heat resistant tape is easily available in markets this tape absolves heat Means if you apply it on specific component, those components do not get hot now how to resold the components to work on a small components moved up the knob of heater option to number two You can also move it to three if you need one thing Very important that the numbers you'll see around the knobs are actually 100, 200, and 300 so you should very careful via using this If you move the knob to Number two it means 200 and a midpoint is 250 for big components, You turn it on three and keep air mini what is mini? mini means that you keep air position in the device between two and three Then you close it to your component for heating as well as touch the device to absolves the components works or not and keep giving heat when it gets too much Then leave it from the tweezer slowly As you can see in the image hold the component from the tweezer and move it very slowly by using finger while giving heat by heat gun continuously the component will separate When silver shine comes from the heat gun Same process you can do for adjustment put component on the place and give heat gives silver shine in this image, there are too many components but don't use the heat gun in complicated areas As you can see, these parts that are fixed on the side can easily move or separate by the Heat gun but using a heat gun in complicated area are not allowed How to solder IC? to solder IC You keep your heat gun point on 350 and keep Air Normal in this picture these ICs can easily be removed so set your heat gun on 350 and keep Air Normal if you have too much waiting for heating that as per need heat can be little increased Micro chips Usually, nowadays micro chips are not not used in a smartphone In the picture you'll see it It can be called microchips

to remove microchips Your heater should be on 45 and air would be in normal like med Remember that you will have to revolve your heat gum while working revolving means do not used a heat gun at one position at a time It must be move or evolve ICs means dose ICs that are punched by machines on a circuit and fixed the corners with any kind of glue Remove this IC Take a knife that is used in biological laboratory and feed it until unless it gets red from front remember one thing that paste must use in fixing chips, so take the hated knife and place it slowly, slowly as you'll see in the video in this process hated knife easily move into the chip This BGA chip, similarly remove as previous you're a hater should be on 45 and air would be a normal like med use paste and remove the chip but if you place this BGA chip to another circuit, then you will have to make balls

Ball making work is very expensive and demandable in the image This is called BGA Kit the black paper you'll see is that different templates now Put down the IC under that template, then you will do it It becomes balls for pasting the IC This liquid is the best This paste works perfectly and this is strong also as you are watching the process to remove the IC is same as you have already seen, but this is very fragile so the heat it lightly in this process Keep air in mad then move it on 3 while working and heat must be in between 3 to 4 when You'll see the little bubbles while heating it means the IC IC is resolder Now Stop the heat gun and wait for getting IC Cool Then check it These are filter ICs to remove These move heater point on 4

5 and if needed, move to 5 and air always normal When IC is remove it looks like this as an video As you can see these walls are clean by using soldering iron Then it places under that kind of net As these silver prints can be seen then pays the pump bob that is available in the market hold the circuit by using a screwdriver and then apply the heat by the heat gun

Source: Youtube

Md. Elias
admin@test.nygadgetfix.com
No Comments

Sorry, the comment form is closed at this time.

Chat with us
Chat with us
Questions, doubts, issues? We're here to help you!
Connecting...
None of our operators are available at the moment. Please, Send us an email, we will get back to you as soon as possible. Thanks.
Our operators are busy. Please try again later
:
:
:
Have you got question? Write to us!
:
:
This chat session has ended
Was this conversation useful? Vote this chat session.
Good Bad